Home > Error Code > Balboa Hot Tub Error Codes

Balboa Hot Tub Error Codes

Contents

SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition. dr Inadequate water detected in heater.. Check for clogged filter. his comment is here

FLO* = Flow Switch (heater is deactivated. The causes of low water flow in a spa include: Dirty spa filter cartridge Closed or partially closed valves or jets Pump has an air lock, or has lost prime Low If you need assistance with spa trouble codes, you can call us anytime at 800-770-0292  Happy Hot Tubbin' Daniel Lara Hot Tub Works Tags: hot tub error code, Clean or replace the spa filter, open all the jets and turn the pump on high. https://spacare.com/spasideerrorcodes.aspx

Balboa Hot Tub Error Codes

Note: This auxiliary freeze protection functions at all times, even when another fault condition has occurred and has otherwise shut the spa down. Contact the dealer or service technician.Open Flow SwitchMeans that the switch is malfunctioning and staying open, the filter cartridge for the circulation pump is dirty or an air lock issue occurred Please note that the Balboa Error Codes cover all circuit board manufactured by Balboa including Cal Spa, Marquis Spa, Master Spa and many others. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open

ILOC Interlock failure - possible pump or ozone spike. (---) Unknown water temperature. (Displays when first powered up after refill). Heater is deactivated.Sn2 = Nonfunctional temperature sensor. Contact the dealer or service technician.Shorted Sensor (Hi-Limit)The hi-limit temperature sensor is malfunctioning; heater is taken offline automatically when this happens.Do not attempt to service on your own. Coleman Spa Error Codes Make sure that they are open.• Clean the filter(s), waterline skimmer and footwell suction for any blockage..• In extremely hot weather, check for proper cabinet ventilation.• Check for excessive filter duration.

The following is a list of most probable causes of this message. All Rights Reserved. In the summer and especially in warm regions, ambient temperature may be high enough to overheat the spa naturally. You can follow any responses to this entry through the RSS 2.0 feed.

Snb = Spa is shut down. Hot Tub Error Code Oh FC Freeze protection. NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. So - FLOW.

Vita Spa Error Codes

Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat.Jacuzzi Hot Tubs J-400 Error Conditions/ http://www.hottubworks.com/blog/spa-error-codes-the-big-list/ Sn3 Open or shorted sensor ( heater disabled). Balboa Hot Tub Error Codes Spa is shut down. Marquis Spa Error Codes In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair.

IC, ICE, ICE2 Freeze Condition detected; Warm up procedure begins. http://divxvar.com/error-code/computer-error-codes-list.html No action is necessary. Once again these can be caused by a flow issue. Hold Panel sensors have been pressed too many times in a short period of time. How To Fix Flo Error Hot Tub

One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit SL = Sleep mode Brett Aqualine Control Systems for Spas or Hot Tubs: OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° FFL = Pressure switch OH Over heat. weblink The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes.

You will hear the sound of escaping air, then water will start dripping. Balboa Spa Control Manual CTI Spa Side Error Codes For more information regarding CTI tech support click here th1/39 On startup indicates temperature probe problem. OH, HH or HOT trouble codes, or a hot tub overheating is not usually a spa heater problem - it is almost always a flow problem, and when it's not a

Status of the heater element is unknown.

Entire system is disabled. This setting is not user-programmable.This condition does not kick in until the water temperature climbs to 95°F (35°C). Check to see if the water level is below the lowest pillow but above the jets. Gecko Spa Pack Error Codes th3/39 = On startup indicates water temperature less than 39° F.

HFL = Substantial difference between temperature sensors detected. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. The Cover Guy is one of the original online Replacement Hot Tub Cover stores in North America! check over here ACC (Applied Computer Controls)Systems for Spas or Hot Tubs: CoLd = Temperature in the spa heater housing is below 40° F.

Pressure switch is not working. The spa system’s ability to cool itself down is directly affected by ambient temperatures. drops. The spa deactivates in this situation.DO NOT GET INTO THE WATER.

Could indicate a flow problem. Spa unusable. PSoH Pressure switch open with high pump. OHH Overheat.

Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa HOT Circuit Board temperature has exceeded acceptable limit.